Product Search
 
Product Catalogue
New Products
Contact Us
FAQs
About Us
News & Events
Downloads
Enter your email address below to receive our newsletter.
 Text     HTML
 
Products » Clamp on Meters

Clamp on Meters
 
 Previous 
 1  2  3 
 Next 
 
 
AC/DC Clamp Meter
Click image to enlarge - AC/DC Clamp Meter
Click image to enlarge
MODEL: TES 3050

  • True RMS reading 1000A
  • Auto-Zero for DCA
  • Autoranging on V, , A, Hz
  • Bar-Graph indication
  • 3-3/4 Digital LCD with Bar-graph
  • Autoranging on Volt, Ohm,
    Current, Frequency measurements
  • Auto-power off
  • Data Hold mode
  • MAX/MIN Hold mode
  • Zero Adjustment/Relative Reading
  • Peak Hold Mode (only ACV and ACA range)
  • Two years warranty
 
 
Power AC/DC Clamp Meter
MODEL: TES 3063

  • RS-232 Interface to talk with PC
  • 4 digits with dual Display LCD
  • Amp/Voltage Frequency Measurement
  • Dual display KW + FP, KVA + PF, V+A
  • 4000 Continuity Point Data Logger, 25 point manual Data Logger
  • True Power / Apparent Power / Power Factor Measurement
  • True RMS. V, A, W, cap, Ind, phase indicator
  • MIN / MAX Measurement
  • PEAK HOLD Detector
  • Dual display A + Hz , V + Hz
Click image to enlarge - Power AC/DC Clamp Meter
Click image to enlarge
 
 
TRMS Power Clamp Meter - HVAC
Click image to enlarge - HVAC Trms Clamp Meter
Click image to enlarge
MODEL: TES 3079M

  • HVAC Application:
  • Check current draw in motors and compressors.
  • Use MAX/MIN recording in the temperature mode
  • Test run/start capacitors
  • Confirm low voltage control signals
  • Measure flame safeguard device current draw
  • Confirm power sources
  • Analyze temperature and power data with the aid of the time stamp
  • Insulation test up to 100M Ohms


  • Electrical Application:
  • Check for energized circuits and balance loads
  • 1-phase/3-phase (3P3W/3P4W) power analyzer
  • Evaluate electrical contacts
  • Capture inrush current readings of motor
  • Determine peak power demand periods
  • Verify line voltage stability
  • Monitor motors and other loads for excess heat
  • Check motor run/ start capacitor values
  • Check 3-phase sequence
 
 
AC/DC Clamp Meter
MODEL: TES 3082

  • True RMS Reading
  • 4000 Count Reading
  • AC/DC 600A
  • DCA One-touch-Zero
  • Auto Power Off
Click image to enlarge - AC/DC Clamp Meter
Click image to enlarge
 
 
AC Clamp Meter
Click image to enlarge - AC/DC Clamp Meter
Click image to enlarge
MODEL: TES 3091-N

  • 3 3/4 digits LCD display, 4000 counts
  • NCV function (Non-contact voltage detection)
  • Data hold function
  • Auto power off (15 minutes)
  • Auto ranging
 
 
AC Clamp Meter
MODEL: TES 3900

  • 1000A AC clamp meter
  • Clamp opening 1.2’’
  • Variable-frequency drives (VFD) V & Hz measurement
  • Data hold, auto hold & peak hold mode
  • Check 3 phase sequence
  • Inrush current measurement
  • Max/Min record mode
  • Data memory & read function
  • CAT.III 1000V / CAT.IV 600V
Click image to enlarge -
Click image to enlarge
 
 
AC/DC Clamp Meter
Click image to enlarge -
Click image to enlarge
MODEL: TES 3910

  • CAT.III 1000V, CAT.IV 600V
  • Max wire diameter : 30mm
  • True RMS reading on AC and DC+AC mode
  • Inrush current measurement
  • Phase Rotation Check (3φ)
  • Variable-frequency drives (VFD) V & Hz measurement
  • Lo-Z voltage measurement to drain ghost voltages
  • μA measurement for HVAC flame sensors
  • mV measurement range to interface with other accessories
  • Crest Factor & Harmonic ratio measurement
  • Inrush current measurement.
  • Data hold, Auto hold & Peak hold mode.
  • Max/Min record mode.
  • Data memory & read function
 
 
Clamp AC/DC
MODEL: TES ADC-1000

  • Ideal for large size cable 500mm
  • One touch zero adjustment
  • Can connect to an oscilloscope for current waveform
Click image to enlarge - AC/DC Clamp
Click image to enlarge
 
 Previous 
 1  2  3 
 Next 
 
 
©2020 MTP Instruments Inc. All rights reserved.